
Aus Klammeroberteil, Klemmenunterteil, Schraubentyp und Mutter kann eine Vielzahl an Gitterrostbefestigungssätzen erstellt werden.
ARNELL Befestigungssätze können vormontiert oder als SET lose bestellt werden. Dabei profitieren Sie immer von der Sicherheit alle Komponenten vollständig zu haben.
Filter
HILTI X-MGR M60
Prices visible after login / registration
Clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to a grating height 40 mm hot-dip galvanized Unmounted kit consisting of: HILTI X-MGR retaining flange Cylinder head screw DIN 912 M8x60, hot-dip galvanized Grating fastenings are currently not subject to CE standards, but must in accordance with the statutory provisions applicable to the applicationbe used.
Prices visible after login / registration
SET assembled, LOWER PART 31, SLOTTED
Prices visible after login / registration
Befestigungssatz montiert für Maschenteilung 33x11/34x11 mm
Füllstabsweite mindestens 9 mm
Verwendung bis Rosthöhe 50 mm
feuerverzinkt nach DIN EN ISO 1461
Befestigungssatz bestehend aus:
Unterteil 31, feuerverzinktBecherschraube M8x70, Stahl 4.8,feuerverzinktVierkantmutter DIN 557 M8, feuerverzinkt
Gitterrostbefestigungen unterliegen derzeit keinen CE-Normen, müssen jedoch gemäß den für den Anwendungsfall geltenden gesetzlichen Bestimmungen
verwendet werden.
Prices visible after login / registration
SET assembled, LOWER PART 31, SLOTTED
Prices visible after login / registration
Befestigungssatz montiert für Maschenteilung 33x11/34x11 mm
Füllstabsweite mindestens 9 mm
Verwendung bis Rosthöhe 40 mm
feuerverzinkt nach DIN EN ISO 1461
Befestigungssatz bestehend aus:
Unterteil 31, feuerverzinktBecherschraube M8x60, Stahl 4.8,feuerverzinktVierkantmutter DIN 557 M8, feuerverzinkt
Gitterrostbefestigungen unterliegen derzeit keinen CE-Normen, müssen jedoch gemäß den für den Anwendungsfall geltenden gesetzlichen Bestimmungen
verwendet werden.
Prices visible after login / registration
SET assembled, LOWER PART 31, SLOTTED
Prices visible after login / registration
Befestigungssatz montiert für Maschenteilung 33x11/34x11 mm
Füllstabsweite mindestens 9 mm
Verwendung bis Rosthöhe 60 mm
feuerverzinkt nach DIN EN ISO 1461
Befestigungssatz bestehend aus:
Unterteil 31, feuerverzinktBecherschraube M8x80, Stahl 4.8,feuerverzinktVierkantmutter DIN 557 M8, feuerverzinkt
Gitterrostbefestigungen unterliegen derzeit keinen CE-Normen, müssen jedoch gemäß den für den Anwendungsfall geltenden gesetzlichen Bestimmungen
verwendet werden.
Prices visible after login / registration
SET UPPER PART 23, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 12 mm Use up to grating height 40 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x60, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 23, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 12 mm Use up to grating height 60 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x80, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 23, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 12 mm Use up to grating height 50 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x70, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 23S, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 22 mm Use up to grating height 60 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23S, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x80, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 23S, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 22 mm Use up to grating height 50 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23S, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x70, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 23S, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set with upper part mounted over 2 cross bars Mesh width at least 30 mm Cross bar pitch in maximum 22 mm Use up to grating height 40 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 23S, hot-dip galvanized Lower part 31, hot-dip galvanized Countersunk head screw DIN 7991 M8x60, steel 8.8, galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 40 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 31, hot-dip galvanized Hexagon head screw DIN 933 M8x60, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 60 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 31, hot-dip galvanized Hexagon head screw DIN 933 M8x80, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 50 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 31, hot-dip galvanized Hexagon head screw DIN 933 M8x70, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 31, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 60 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 32, hot-dip galvanized Hexagon head screw DIN 933 M8x80, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 32, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 40 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 32, hot-dip galvanized Hexagon head screw DIN 933 M8x60, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 32, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 50 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 32, hot-dip galvanized Hexagon head screw DIN 933 M8x70, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration
SET UPPER PART 5, LOWER PART 47, hot-dip galvanized
Prices visible after login / registration
Mounted clamp set for mesh 33/34 mm Cross bar width at least 26 mm Use up to grating height 20 mm Hot-dip galvanized acc. DIN EN ISO 1461 Clamp set consists of: Upper part 5, hot-dip galvanized Lower part 47, hot-dip galvanized Hexagon head screw DIN 933 M8x50, steel 4.8, hot-dip galvanized Square nut DIN 557 M8, hot-dip galvanized Grating fixtures are currently not subject to CE standards but must comply with the legal requirements applicable to the application.
Prices visible after login / registration